An independent woodworking journalMake something worth keeping.
Good wood.
Useful knowledge.
A little patience.
The Wood Journal

How to Reduce Thickness Planer Snipe Before Cutting Parts to Length

If the first or last section of a planed board is thinner than its middle, do not immediately lower the cutterhead for another pass. First identify the length and location of the dip. Another pass can reproduce the same defect while making the whole board thinner.

Snipe is an end-of-board problem, so the most useful first question is whether you can keep it outside the finished part. Leave project stock long until you have tested the planer setup and know how much clean length remains.

Confirm that the defect is actually snipe

With the machine stopped, examine the board under low-angle light. Place a reliable straightedge along the face and look for a short depression near either end. Measure thickness at several points rather than relying only on how the surface feels.

A rough torn patch following difficult grain is a different issue. So is a ridge running along the entire board. Write down what you can observe: a dip at the leading end, a dip at the trailing end, both, or an uneven surface along the whole length.

DEWALT explains snipe in its DW735 manual as a depression that can occur when an unsupported end drops and the opposite end lifts toward the cutterhead. Its guidance emphasizes keeping stock level against the bed and supporting long pieces. Those principles help diagnosis, but use your own machine's instructions for adjustments and stock limits. DW735 instruction manual. If the PDF does not open, use Downloads and manuals on the DW735 product page

Set up the support before the test pass

Disconnect power before inspecting or adjusting the planer. Clean chips from the bed and extension tables as the manual directs. Check that the stand is stable and that a long board has clear space on both sides of the machine.

Position additional supports so they carry the stock without levering it upward or steering it sideways. A roller stand that is merely nearby does not establish the right height. Check its relationship to the planer bed with the machine off and the intended stock supported.

Use a straight, expendable board for the first trial. A severely bowed board introduces another variable and makes the result harder to interpret. A thickness planer needs an appropriate reference face; repeatedly passing distorted stock does not reliably turn it into a flat board.

Change one thing at a time

Label the test board's feed direction and note the starting thickness. Make a permitted light pass, following the machine's feed and handling instructions. Let the machine feed the stock rather than pulling it out to hurry the last section.

After the pass, record the affected length at each end. If you change support height, keep the other conditions similar for the next trial. If you change depth of cut, do not simultaneously change the board species, length and support arrangement.

Record the affected length at each end and the thickness difference from the middle. A shorter dip may still be deep enough to spoil a joint; a shallower dip may still extend inside the intended cut line. Compare both measurements after each adjustment.

Reserve length using the observed result

Imagine a practice board needs to provide a 600 mm finished part. Your tests show an unacceptable dip within 50 mm of one end and 60 mm of the other. The arithmetic minimum is 710 mm before allowing for saw cuts and any additional trimming margin: 600 + 50 + 60.

That example is a layout calculation, not a universal recommendation to discard those amounts. Mark the actual defect boundary on your own board. Keep your final cut line beyond it, and allow for the saw kerf on the waste side.

For several parts, sketch the complete sequence of clean areas, cut lines and waste. You may recover short components from sound sections that cannot provide a long rail. Avoid planning a critical joint at the edge of an uncertain depression merely to save a small amount of timber.

Know when to stop adjusting

Some planers have carriage locks, table adjustments or maintenance procedures that affect snipe. They are model-specific. Do not copy roller-height settings or cutterhead modifications from a different machine.

If appropriate support and the manufacturer's normal adjustments do not help, consult the troubleshooting section or manufacturer support. A deteriorating result, unexpected noise or visibly damaged components is a reason to stop and investigate, not to compensate with increasingly unusual feeding techniques.

Do not feed stock below the minimum length or thickness just to remove a final defect. Preserve the required guards and keep hands outside the machine's specified danger areas.

Inspect before final sizing

Once the setup gives an acceptable result, plane the remaining stock with the same support arrangement. Check the last board as well as the first; consistency matters more than one successful sample.

Mark the usable area, then cut the parts to finished length. Keep a record of the allowance you needed for this setup, and verify it again when the stock or machine changes.

Owen Mercer
Tools & workshop practice

Owen Mercer

Workshop notes on hand tools, joinery, jigs and the small habits that make a project easier.

Comments

Popular posts from this blog

Lumber Grades At A Glance

Illustrative AI-generated image. Domestic hardwood lumber found at sawmills meets different quality levels or grades as specified by the National Hardwood Lumber Association (NHLA). The basis for this wood grading is the number and size of defect-free clear cuttings in a board, as summarized below, Thickness is not a consideration, though with some species worm holes, gum pockets, and stain are acceptable. FAS (First & Seconds) lumber grade. This premium grade represents the finest lumber yield in a log. Generally, the minimum size board is 6" wide by 8' long which yields a minimum of 83 1/3% clear cuttings on its poorest face. F1F (FAS One Face) lumber grade. The best face grades as clear FAS; the worst, as #1 common, containing some knots. Selects lumber grade. Close to a FAS board. A Select board must be a minimum of 4" wide and 6' long and yield a minimum of 83 1/3% clear cuttings, but only on one face with #1 common on the worst face. #...

How to buy Sawmill Hardwood and Save (Part 1)

Illustrative AI-generated image. When you visit a home center to purchase hardwood lumber, more than likely you'll encounter limited quantities, limited species, and through-the-roof pricing. In some cases, you're paying for that shiny cellophane wrapper. Before you sell your tools and steer toward a different hobby, you need to check out the benefits of shopping at a lumber sawmill. While some mills service only the commercial building industry. make pallets, or ship woods overseas, many gladly sell to the local woodworker. Here is where you'll find great variety and huge savings. If the special lingo and ways in which sawmills sell hardwood have kept you at bay, let us help you shop like a pro. First things first: finding a sawmill. While your local yellow pages will yield results when you look under "Sawmills” or “Lumber-Retail," members of 10 cal woodworking clubs, woodworking friends, or woodworking specialty stores may serve as better sources for locati...

4-Step Antique Finish

Create a fool-the-eye timeworn look. Some projects, like wine server for your wood cabinet, are not unlike a pair of blue jeans, Both look better after a few years of regular use. To create that well-worn look wood finish, I have come up with a finishing schedule that can add a century's worth of character in less time than it would take to stonewash a new pair of Levis. At first glance, this four-step finish might appear demanding, bur keep reading. As you'll soon learn, this special finish amounts to little more than a combination of a few basic techniques you've probably used before. The “pickling" and - “highlighting” I use aren't much different than whitewashing a fence. Simply brush on the color and then wipe some off until it looks good to you. And after each step you'll apply a quick-drying seal coat to save your work. Besides providing an additional decorative element to your work, antiquing has some practical advantages. Adding color to t...

It starts with
a piece of wood.

Unfinished Wood is a collection of practical ideas for the workshop: choosing your materials, solving small problems, and bringing out the character in what you make.

The journal voices

Owen Mercer
Tools & workshop practice

Owen Mercer

Workshop notes on hand tools, joinery, jigs and the small habits that make a project easier.

Ben Harlow
Wood & materials

Ben Harlow

Practical guides to choosing lumber, understanding grain and planning for wood movement.

Daniel Reed
Surface & finish

Daniel Reed

Notes on sanding, test samples, color and finishes that let the character of the wood show through.

Search This Blog